欢迎光临上海光春动平衡机设备有限公司官网! 咨询热线:13636433206

请登陆后台添加(banner)标题

请登陆后台添加(banner)标题

请登陆后台添加(banner)标题

动平衡机添加润滑油要适量!

* 来源 : * 作者 : admin * 发表时间 : 2017-05-17 * 浏览 : 34
动平衡机要时常注意合理添加润滑油,保证动平衡机的正常运行,防止磨损引起机器损坏,但润滑油的不合理添加也会造成一定的影响,下面来看看动平衡机因润滑油问题引起的故障有哪些?
Balancing confidential always pay attention to reasonable to add lubricating oil, ensure the normal operation of the dynamic balancing machine, to prevent wear caused by damage to the machine, but not reasonable to add lubricating oil will cause certain impact, the dynamic balancing machine to see the fault caused by oil problems are there?
1.箱体漏油造成环境污染
1 oil leakage caused by environmental pollution
在动平衡机中,因为油封损伤、密封垫破损、油塞松脱或是油标破损等因素引起箱体漏油,也可能油量过多、油位过高或多次冷启动造成润滑油发生起泡现象,引起通气塞处出现大量漏油而严重污染环境。
In the dynamic balance machine, because the oil seal damage, seal damage, oil removal or cesson oil standard damage caused by oil spill case, may be too much oil, the oil level is too high or several cold start causing lubricating oil foaming phenomenon occurs, causing a large number of oil spills and ventilation plug appeared serious pollution of the environment.
2.油温过高造成器件损坏
2 high temperature device damage
动平衡机运行中,由于润滑油量不足或设备超负荷运转等原因,导致的动平衡机内部润滑油温度快速上升,造成动平衡机内部相关部件产生局部损坏。有些器件由于内应力没有消除,遇热变形大造成动平衡机精度下降,有些器件在高温情况下材料强度降低引起损坏。另外,一些运转不灵活、严重损耗动力的动平衡机在作业过程中,当有异物侵入时,可能传动件被卡住,出现运转不均匀或振动不正常等现象。
In the operation of the dynamic balancing machine, due to the insufficient amount of lubricating oil or overload operation of the equipment, the internal lubricating oil temperature of the dynamic balancing machine increases rapidly, resulting in the local damage of the internal parts of the balancing machine. Some devices due to the internal stress is not eliminated, in case of large deformation caused by dynamic balancing machine precision decreased, some devices in the case of high temperature strength of the material to reduce damage. In addition, some of the operation is not flexible, serious loss of power in the operation of the dynamic balancing machine in the course of work, when a foreign body intrusion, the transmission parts may be jammed, the phenomenon of uneven operation or abnormal vibration.
3.动平衡机内部结构设计不规范
3 dynamic balancing machine internal structure design is not standard
在动平衡机结构中,由于检查孔上面的盖板设计的过于单薄,上紧螺丝后局部容易发生变形而产生接触缝隙导致漏油,制造过程中铸件没有进行退火处理而发生变形产生间隙导致漏油,还可能由于箱体上没有设计回油槽,当过多的润滑油累积在减速器箱体的端盖和结构结合面处时,压差造成润滑油从结合间隙处向外泄漏。
In dynamic balancing machine structure, because the cover above the inspection hole design is too thin to tighten the screws after local deformation and contact gap easily lead to leakage, in the manufacturing process of castings without annealing and deformation of oil leakage caused by the gap, may also be in the box without back design of oil tank, when the oil over the accumulated in the gear box cover and the structure of the interface, the pressure difference caused by oil leakage outward from the gap with.
动平衡机在使用之前一定要合理添加润滑油,当然也要注意防止因润滑油问题对动平衡机造成的影响,以免发生以上故障,从而对动平衡机造成破坏,影响了动平衡机的使用。
Balancing machine before use must be reasonable to add lubricating oil, of course also should pay attention to prevent lubricating oil problems of dynamic balancing machine which, in order to avoid the occurrence of the above faults, resulting in the destruction of the dynamic balancing machine, the impact of the use of dynamic balancing machine.